Carl's Place C-Series DIY Golf Simulator Enclosure Kit with Impact Screen

The Carl's Place C-Series DIY Golf Simulator Enclosure Kit with Impact Screen gives you a screen and enclosure system for building a home golf simulator. Choose the enclosure size and screen material that suit your room, then complete the frame with the matching pipe kit or locally sourced EMT.

Choose your size and screen: Six enclosure sizes are available with Standard, Preferred, Premium, or High-Contrast Gray impact screen material. The borderless bottom design brings the projected image down to floor level for a continuous transition from your hitting area to the screen.

What's included: Your selected impact screen, black nylon enclosure surround, steel fittings, and the screen-fastening hardware described below. Match optional accessories to the enclosure size you select.

Framing pipes are sold separately. Add the Carl's Place Pipe Framing Kit for pre-cut pipes, or source 1-inch EMT locally and follow the supplied cut sheet. A projector, launch monitor, hitting mat, putting turf, and simulation software are not included.

Check the actual dimensions before ordering. The listing size is not the full outside measurement. Use the Specifications section and original cut sheets below, and allow additional room for your swing, hitting position, and equipment clearances.

What's Included

Your Choice of Impact Screen Material
Choose from Carl's Place Standard, Preferred, Premium, or High-Contrast Gray impact screen material. Each option will provide a floor-to-turf image with a bottomless edge and minimal bounce back.

Black Nylon Enclosure
The nylon enclosure provides for a tough surface to catch any stray shots that attempt to leave the simulator while also surrounding the simulator to provide for an immersive experience.

Steel Fittings
Corner fittings are included to connect the framing pipes for your simulator. We highly recommend that you purchase the Carl's Place Pipe Framing Kit accessory, otherwise you will have to purchase 1-inch EMT pipes from your local hardware store to complete the assembly of your DIY Enclosure.

Ball Bungees and Zip Ties
You will receive releasable zip ties as well as 6" and 9" ball bungees to secure your screen to the frame. Extras are included so you can experiment with finding the perfect balance of tension and slack for your screen. How close you are hitting to the screen, ball speed, clubs, and spin rate all impact the responsiveness and acoustics of your screen.

Accessories

Net Wall Extensions
Net Wall Extensions attached onto your frame enclosure and catch errant shots to the left and right of the hitting area so they do not hit the walls of your home. Hook and loop strips are used to attach the Net Wall Extensions to the frame and sandbags (fill not included) at the bottom hold them in place.

Pipe Framing Kit
The Pipe Framing Kit is an essential accessory should you wish to have a hassle-free setup. The kit includes black, powder-coated EMT pipes that are pre-cut to the exact length required to fit your enclosure dimensions.

Foam Inserts
The Foam Insert Kit protects your enclosure frame from errant shots. The foam inserts are the perfect length and profile and are inserted behind the screen flaps of the DIY Golf Simulator Enclosure to give you extra peace of mind while hitting balls.



Safety Baffles
Safety Baffles protect the ceiling of your simulator enclosure while hitting higher shots. They are positioned across the width of your simulator enclosure on the ceiling.



Back Cover Kit & Back Cover Pipe Kit
The Back Cover Kit protects from any intruding light on the rear portion of your simulator enclosure. The Back Cover Kit ensures that you will achieve the highest projected image quality while also providing your simulator enclosure with a polished appearance so none of the rear framing is exposed. The Back Cover Pipe Kit is also offered so you do not have to purchase framing pipes from your local hardware store.

Please Note: While purchasing the Pipe Framing Kit, Foam Inserts, Safety Baffle, Back Cover Kit, or Back Cover Pipe Kit, be sure to choose the size that corresponds with your Golf Simulator Enclosure size. *Safety Baffles should match the width of your simulator enclosure.

Specifications

Actual outside frame dimensions

The screen-to-front depth is 59.125 inches. Including the rear backset fitting, the frame footprint is 67.375 inches deep. These are enclosure measurements, not the total playing-space requirement. See the specification drawing and cut sheets below for installation details.

Depths: Available in one standard 59.125" depth, measured from the screen to the front of the frame. The rear backset fitting adds 8.25", for a total footprint depth of 67.375".

Assembly

EMT Requirements
Unless you have purchased the Pipe Framing Kit accessory, you will need to purchase 1-inch EMT (electrical metal tubing) from your local hardware store to complete your frame. Please note, 1-inch EMT is the US trade name of the material, however the true outer diameter is 1.163" or 27mm.

Documents:

• Carl's Place C-Series DIY Golf Simulator Enclosure Kit Assembly Instructions & User Manual
• Carl's Place Back Cover Kit for DIY Golf Simulator Enclosure
  
  

DIY Golf Simulator Enclosure Kit Cut Sheets:

• 7.7'H x 10'W DIY Golf Simulator Enclosure Kit Cut Sheet
• 7.7'H x 13'W DIY Golf Simulator Enclosure Kit Cut Sheet
• 8'H x 8'W DIY Golf Simulator Enclosure Kit Cut Sheet
• 8'H x 10.5'W DIY Golf Simulator Enclosure Kit Cut Sheet
• 8.5'H x 11.5'W DIY Golf Simulator Enclosure Kit Cut Sheet
• 9'H x 12'W DIY Golf Simulator Enclosure Kit Cut Sheet

DIY Golf Simulator Enclosure Back Cover Kit Cut Sheets:

• 7.7'H x 10'W DIY Golf Simulator Enclosure Back Cover Kit Cut Sheet
• 7.7'H x 13'W DIY Golf Simulator Enclosure Back Cover Kit Cut Sheet
• 8'H x 8'W DIY Golf Simulator Enclosure Back Cover Kit Cut Sheet
• 8'H x 10.5'W DIY Golf Simulator Enclosure Back Cover Kit Cut Sheet
• 8.5'H x 11.5'W DIY Golf Simulator Enclosure Back Cover Kit Cut Sheet
• 9'H x 12'W DIY Golf Simulator Enclosure Back Cover Kit Cut Sheet